Article 9220

Title of the article

GRINDING BALLS WITH PARTICULAR ACCURACY 

Authors

Rubtsov Vitaliy Yur'evich, Roll pass designer, rail and structural shop, joint-stock “EVRAZ Nizhny Tagil Metallurgical Plant” (1 Metallurgov street, Nizhny Tagil, Sverdlovsk region, Russia); postgraduate student, Ural Federal University named after the first President of Russia B. N. Yeltsin (19 Mira street, Ekaterinburg, Russia), E-mail: Uriylot@mail.ru
Shevchenko Oleg Igorevich, Doctor of engineering sciences, head of the sub-department of metallurgic technologies, Nizhny Tagil Technological Institute (branch) Ural Federal University named after the first President of Russia B. N. Yeltsin (59 Krasnogvardeyskaya street, Nizhny Tagil, Russia), E-mail: Shevchenko_Oleg@mail.ru
Alypov Pavel Alekseevich, Senior roll pass designer, rail and structural shop, joint-stock “EVRAZ Nizhny Tagil Metallurgical Plant” (1 Metallurgov street, Nizhny Tagil, Sverdlovsk region, Russia), E-mail: Pavel.Alypov@evraz.com
Lebedev Vladimir Alekseevich, Senior specialist of metrology, joint-stock “EVRAZ Nizhny Tagil Metallurgical Plant” (1 Metallurgov street, Nizhny Tagil, Sverdlovsk region, Russia), E-mail: Vladimir.Lebedev@evraz.com 

Index UDK

621.775.26 

DOI

10.21685/2072-3059-2020-2-9 

Abstract

Backgrounds. It is possible to obtain grinding balls production by cross-helical rolling method, with particular accuracy to their geometry. It is relevant to divide produced grinding balls nomenclature into 2 groups of geometric accuracy. It is recomend use of “particular accuracy” to balls intended for heat treatment into the fifth hardness grade. The study object is grinding balls. The research subject is process of grinding balls production on modern equipment with high geometric parameters achievement. The aim of this resurche is it structure the parameters to which accuracy of the grinding balls geometric dimensions on, determining their influence degree, as well as the maximum deviations for proposed group of high accuracy balls.
Materials and methods. The study was carried out in conditions of the EVRAZNTMK JSC rail and beam workshop. Rolling was on modern ball-rolling mill 60-120. The rolls were manufactured at 5-coordinate machining center NORMA L-45, and geometric parameters were controlling on FAROARM measuring machine.
Results. Following limit of geometric accuracy were identified: the limit due to manufacturing quality of deformation tool, the limit in setting ball-rolling mill and the measurement limit. Total limit was calculated under for all sizes of obtained balls. The table with gradation of grinding balls into two groups: ordinary accuracy and high accuracy, indicating maximum deviations in size was compiled.
Conclusions. The study confirms that at now it is possible to obtain increased accuracy balls, which, due to decrease in stress concentration, will be minimally subject to destruction during hardening and external influences. 

Key words

grinding ball, dimension, size deviation, particular accuracy 

Download PDF
References

1. GOST 7524-2015 Shary melyushchie stal'nye dlya sharovykh mel'nits [State Standart 7524-2015 Grinding steel balls for ball mills]. Moscow, 2015. [In Russian]
2. Rubtsov V. Yu., Shevchenko O. I. Aktual'nye problemy sovremennoy nauki, tekhniki i obrazovaniya: tezisy dokladov 76-y Mezhdunar. nauch.-tekhn. konf. [Actual issues of modern science, technology and education: proceeding of the 76th International scientific and technical conference]. Magnitogorsk: Izd-vo Magnitogorsk. gos. tekhn. un-ta im. G. I. Nosova, 2018, vol. 1, pp. 117–118. [In Russian]
3. Rubtsov V. Yu., Shevchenko O. I. Kalibrovochnoe byuro [Calibration bureau]. 2018, no. 13, pp. 20–22. [In Russian]
4. Yur'ev A. B., Atkonova O. P., Korneva L. V. et al. Stal' [Steal]. 2010, no. 4, pp. 90–91. [In Russian]
5. Mokhov G. V. et al. Metallurgiya: tekhnologii, upravlenie, innovatsii, kachestvo: tr. Vseros. nauch.-prakt. konf. [Metallurgy: technology, management, innovation, quality: proceedings of All-Russian scientific and practical conference]. Novokuznetsk, 2009, pp. 204–207. [In Russian]
6. Sakhrayu A., Abdel'khamid S., Mokhand Amokran B., Rassim Yu., Ali B., Abderrakhim B. Metallovedenie i termicheskaya obrabotka metallov [Metallurgy and heat treatment of metals]. 2017, no. 5, pp. 34–38. [In Russian]
7. Yur'ev A. B., Kuznetsov E. L., Atkonova O. P., Kopylov I. V., Zakaulov E. P. Chernaya metallurgiya. Byulleten' NTI ChM [Ferrous metallurgy. Bulletin of scientific, technical and economic information. Bulletin of scientific, technical and economic information]. 2014, no. 6, pp. 42–43. [In Russian]
8. Shevchenko O. I., Trekin G. E., Rubtsov V. Yu., Kurochkin V. V. Innovatsionnye tekhnologii v materialovedenii i mashinostroenii ITMM-2019: materialy 4-y nauch.- prakt. konf. s Mezhdunar. uchastiem, posvyashch. 70-letnemu yubileyu kafedry «Metallovedenie, tekhnologiya termicheskoy i lazernoy obrabotki metallov». [Innovation technologies in material science and machine-building ITMM-2019: proceedongs of the 4th scientific and practical conference with international participation devoted to the 70th anniversary of the sub-department “General metallurgy, metal thermal and laser treatment technology”]. Perm, 2019, pp. 294–297. [In Russian]
9. Shevchenko O. I., Trekin G. E., Rubtsov V. Yu., Kurochkin V. V. Vestnik Permskogo natsional'nogo issledovatel'skogo politekhnicheskogo universiteta. Mashinostroenie i materialovedenie [Bulletin of Perm National Research Polytechnic University. Machine-building and material science]. 2019, vol. 21, no. 3, pp. 110–117. [In Russian]
10. Anikin A. V., Tugushev P. N., Kuznetsov S. A. Nedelya metallov v Moskve: sb. tr. konf. (g. Moskva, 11–14 noyabrya 2014 g.) [Metals week in Moscow: procceding of conference (Moscow, November 11-14, 2014)]. Moscow, 2015, pp. 338–348. [In Russian]
11. Efremenko V. G., Popov E. S., Kuz'min S. O., Trufanova O. I., Efremenko A. V. Metallurg [Metallurgist]. 2013, no. 9, pp. 88–92. [In Russian]
12. Rubtsov V. Yu. Aktual'nye problemy sovremennoy nauki, tekhniki i obrazovaniya [Actual issues of modern science, technology and education]. 2017, vol. 1, pp. 90–93. [In Russian]
13. Kotenok V. I., Podobedov S. I. Metallurg [Metallurgist]. 2001, no. 9, pp. 45–47. [In Russian]
14. Kotenok V. I. Razvitie teorii formoobrazovaniya profiley v vintovykh kalibrakh i sozdanie vysokoeffektivnykh protsessov i oborudovaniya dlya prokatki detaley mashin: dis. d-ra tekhn. nauk [Development of the theory of forming profiles in screw calibers and the creation of highly efficient processes and equipment for rolling machine parts: dissertation to apply for the degree of the doctor of engineering sciences]. Moscow, 2005, 342 p. [In Russian]
15. Rubtsov V. Yu., Shevchenko O. I. Chernaya metallurgiya [Ferrous metallurgy]. 2018, no. 8 (1424), pp. 58–63. [In Russian]
16. Rubtsov V. Yu., Shevchenko O. I., Zagrebaylov N. M. Molodezh' i nauka: materialy Mezhdunar. nauch.-prakt. konf. (25 maya 2018 g.): v 2 t. [Youth and Science: proceedings of International scientific and practical conference (May 25, 2018): in 2 volumes]. Nizhniy Tagil: NTI (filial) UrFU, 2018, vol. 1, pp. 18–23. [In Russian]
17. GOST 6507–90. Mikrometry. Tekhnicheskie usloviya [State Standart 6507-90. Micrometers. Specifications]. Moscow, 1990. [In Russian]
18. RD 50-98-86 «Metodicheskie ukazaniya. Vybor universal'nykh sredstv izmereniy lineynykh razmerov do 500 mm. (Po primeneniyu GOST 8.051-81)» [RD 50-98-86 “Methodical instructions. Selection of universal measuring instruments for linear dimensions up to 500 mm. (By application of the State Standart 8.051-81)”]. Moscow, 1986. [In Russian]
19. GOST 8.051–81. GSI. Pogreshnosti, dopuskaemye pri izmerenii lineynykh razmerov do 500 mm. [State Standart 8.051-81. GSI. Inaccuracies allowed when measuring linear dimensions up to 500 mm.]. Moscow, 1981. [In Russian]
20. GOST 2590–2006. Prokat sortovoy stal'noy goryachekatanyy kruglyy. Sortament [State Standart 2590-2006. Hot-rolled high-quality steel round. Assortment]. Moscow, 2006. [In Russian]

 

Дата создания: 31.08.2020 08:37
Дата обновления: 31.08.2020 14:21